MACH220-10 データシートの表示（PDF） - Advanced Micro Devices
部品番号
コンポーネント説明
メーカー
MACH220-10 Datasheet PDF : 33 Pages
| |||
ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . 65°C to +150°C
Ambient Temperature
with Power Applied . . . . . . . . . . . . . –55°C to +125°C
Supply Voltage with
Respect to Ground . . . . . . . . . . . . . –0.5 V to +7.0 V
DC Input Voltage . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
DC Output or
I/O Pin Voltage . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V
Latchup Current
(TA = 0°C to +70°C) . . . . . . . . . . . . . . . . . . . . 200 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent device failure. Functionality at or above
these limits is not implied. Exposure to Absolute Maximum
Ratings for extended periods may affect device reliability.
Programming conditions may differ.
AMD
OPERATING RANGES
Commercial (C) Devices
Temperature (TA) Operating
in Free Air . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Supply Voltage (VCC) with
Respect to Ground . . . . . . . . . . . . +4.75 V to +5.25 V
Operating ranges define those limits between which the func-
tionality of the device is guaranteed.
DC CHARACTERISTICS over COMMERCIAL operating ranges unless otherwise specified
Parameter
Symbol
Parameter Description
Test Conditions
Min Typ Max Unit
VOH
VOL
VIH
VIL
IIH
IIL
IOZH
IOZL
ISC
ICC
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input HIGH Leakage Current
Input LOW Leakage Current
Off-State Output Leakage
Current HIGH
Off-State Output Leakage
Current LOW
Output Short-Circuit Current
Supply Current (Typical)
IOH = –3.2 mA, VCC = Min
VIN = VIH or VIL
IOL = 16 mA, VCC = Min
VIN = VIH or VIL
Guaranteed Input Logical HIGH
Voltage for all Inputs (Note 1)
Guaranteed Input Logical LOW
Voltage for all Inputs (Note 1)
VIN = 5.25 V, VCC = Max (Note 2)
VIN = 0 V, VCC = Max (Note 2)
VOUT = 5.25 V, VCC = Max
VIN = VIHor VIL (Note 2)
VOUT = 0 V, VCC = Max
VIN = VIHor VIL (Note 2)
VOUT = 0.5 V, VCC = Max (Note 3)
VCC = 5 V, TA = 25°C, f = 25 MHz (Note 4)
2.4
V
0.5 V
2.0
V
0.8 V
10 µA
–100 µA
10 µA
–100 µA
–30 –130 mA
205
mA
Notes:
1. These are absolute values with respect to device ground and all overshoots due to system or tester noise are included.
2. I/O pin leakage is the worst case of IIL and IOZL (or IIH and IOZH).
3. Not more than one output should be shorted at a time and duration of the short-circuit should not exceed one second.
VOUT = 0.5 V has been chosen to avoid test problems caused by tester ground degradation.
4. Measured with a 12-bit up/down counter pattern. This pattern is programmed in each PAL block and is capable of being
loaded, enabled, and reset.
MACH220-12/15/20 (Com’l)
11
Share Link: 