AN87C196CA18 データシートの表示（PDF） - Intel

部品番号

コンポーネント説明

メーカー

AN87C196CA18

Advanced 16-Bit CHMOS Microcontroller

Intel 

Automotive — 87C196CA 18 MHz Microcontroller

4.3

DC Characteristics

Table 5.

DC Characteristics (Sheet 1 of 2)

Symbol

Parameter

Min Typical Max

Units

Test Conditions

VCC supply current

ICC

(–40°C to +125°C

ambient)

ICC1

Active mode supply

current (typical)

50

90

mA

XTAL1 = 18 MHz,

50

mA

VCC = VPP = VREF = 5.25 V

(While device is in reset)

IREF

A/D reference supply

current

2

5

mA

IIDLE

IPD

Idle mode current

Powerdown mode

current

15

40

mA

XTAL1 = 18 MHz,

VCC = VPP = VREF = 5.25 V

50

µA

VCC = VPP = VREF = 5.25 V

(Note 4)

VIL

Input low voltage

(all pins)

–0.5 V

0.3 VCC

V

VIH

Input high voltage (all

pins)

0.7 VCC

VCC + 0.5

V (Note 5)

Output low voltage

VOL

(outputs configured as

push/pull)

Output high voltage

VCC – 0.3

VOH

(outputs configured as VCC – 0.7

complementary)

VCC – 1.5

ILI

Input leakage current

(standard inputs)

0.3

0.45

1.5

±10

IOL = 200 µA (Note 3)

V IOL = 3.2 mA

IOL = 7.0 mA

IOH = – 200 µA (Note 3)

V IOH = – 3.2 mA

IOH = – 7.0 mA

µA VSS ≤ VIN ≤ VCC (Note 2)

ILI1

Input leakage current

(Port 0—A/D inputs)

±1.5

µA VSS ≤ VIN ≤ VCC

IIH

Input high current (NMI

pin)

+175

µA VSS ≤ VIN ≤ VCC

SLPINT (P5.4) and

VOH1

HLDA (P2.6) Output

2.0

high voltage in RESET

V IOH = 0.8 mA (Note 8)

VOH2

Output high voltage in

RESET

VCC – 1 V

V IOH = – 15 µA (Notes 1, 6)

IOH2

Output High Current in

RESET

–30

–75

–90

–120

–240

–280

VOH2 = VCC – 1.0 V

µA VOH2 = VCC – 2.5 V

VOH2 = VCC – 4.0 V

NOTES:

1. All BD (bidirectional) pins except P5.5/INST and P2.7/CLKOUT which are excluded due to their not being

weakly pulled high in reset. BD pins include Port1, Port 2, Port3, Port4, Port5, and Port6.

2. Standard Input pins include XTAL1, EA#, RESET#, and Ports 1,2,3,4,5,6 when configured as inputs.

3. All bidirectional I/O pins when configured as outputs (push/pull).

4. Typicals are based on limited number of samples and are not guaranteed. The values listed are at room

temperature and VREF = VCC = 5.0 V.

5. VIH max for Port0 is VREF + 0.5 V.

6. Refer to “VOH2/IOH2 Specification” errata #1 in errata section of this datasheet.

7. This specification is not tested in production and is based upon theoretical estimates and/or product

characterization.

8. Violating these specifications in reset may cause the device to enter test modes (P5.4 and P2.6).

Datasheet

9

Share Link: