M29W004B データシートの表示（PDF） - STMicroelectronics

部品番号

コンポーネント説明

メーカー

M29W004B

4 Mbit (512Kb x8, Boot Block) Low Voltage Single Supply Flash Memory

STMicroelectronics 

M29W004T, M29W004B

Table 10. Polling and Toggle Bits

Mode

DQ7 DQ6 DQ2

Program

Erase

DQ7

0

Toggle 1

Toggle Note 1

Erase Suspend Read

(in Erase Suspend

block)

1

1 Toggle

Erase Suspend Read

(outside Erase Suspend

block)

DQ7

DQ6

DQ2

Erase Suspend Program DQ7 Toggle N/A

Note: 1. Toggle if the address is within a block being erased.

’1’ if the address is within a block not being erased.

Toggle Bit (DQ2). This toggle bit, together with

DQ6, can be used to determine the device status

during the Erase operations. It can also be used to

identify the block being erased. During Erase or

Erase Suspend a read from a block being erased

will cause DQ2 to toggle. A read from a block not

being erased will set DQ2 to ’1’ during erase and

to DQ2 during Erase Suspend. During Chip Erase

a read operation will cause DQ2 to toggle as all

blocks are being erased. DQ2 will be set to ’1’

during program operation and when erase is com-

plete. After erase completion and if the error bit

DQ5 is set to ’1’, DQ2 will toggle if the faulty block

is addressed.

Error Bit (DQ5). This bit is set to ’1’ by the P/E.C.

when there is a failure of programming, block

erase, or chip erase that results in invalid data in

the memory block. In case of an error in block erase

or program, the block in which the error occured or

to which the programmed data belongs, must be

discarded. The DQ5 failure condition will also ap-

pear if a user tries to program a ’1’ to a location that

is previously programmed to ’0’. Other Blocks may

still be used. The error bit resets after a Read/Reset

(RD) instruction. In case of success of Program or

Erase, the error bit will be set to ’0’ .

Erase Timer Bit (DQ3). This bit is set to ’0’ by the

P/E.C. when the last block Erase command has

been entered to the Command Interface and it is

awaiting the Erase start. When the erase timeout

period is finished, after 50µs to 90µs, DQ3 returns

to ’1’.

Coded Cycles

The two Coded cycles unlock the Command Inter-

face. They are followed by an input command or a

confirmation command. The Coded cycles consist

of writing the data AAh at address 5555h during the

first cycle. During the second cycle the Coded

cycles consist of writing the data 55h at address

2AAAh. A0 to A14 are valid, other address lines are

’don’t care’. The Coded cycles happen on first and

second cycles of the command write or on the

fourth and fifth cycles.

Instructions

See Table 8.

Read/Reset (RD) Instruction. The Read/Reset

instruction consists of one write cycle giving the

command F0h. It can be optionally preceded by the

two Coded cycles. Subsequent read operations will

read the memory array addressed and output the

data read. A wait state of 10µs is necessary after

Read/Reset prior to any valid read if the memory

was in an Erase mode when the RD instruction is

given.

Auto Select (AS) Instruction. This instruction

uses the two Coded cycles followed by one write

cycle giving the command 90h to address 5555h

for command set-up. A subsequent read will output

the manufacturer code and the device code or the

block protection status depending on the levels of

A0 and A1 The manufacturer code, 20h, is output

when the addresses lines A0 and A1 are Low, the

device code, EAh for Top Boot, EBh for Bottom

Boot is output when A0 is High with A1 Low.

The AS instruction also allows access to the block

protection status. After giving the AS instruction, A0

and A6 are set to VIL with A1 at VIH, while A13-A18

define the address of the block to be verified. A read

in these conditions will output a 01h if the block is

protected and a 00h if the block is not protected.

Program (PG) Instruction. This instruction uses

four write cycles. The Program command A0h is

written to address 5555h on the third cycle after two

Coded cycles. A fourth write operation latches the

Address on the falling edge of W or E and the Data

to be written on the rising edge and starts the

P/E.C. Read operations output the Status Register

bits after the programming has started. Memory

programming is made only by writing ’0’ in place of

’1’. Status bits DQ6 and DQ7 determine if program-

ming is on-going and DQ5 allows verification of any

possible error. Programming at an address not in

blocks being erased is also possible during erase

suspend. In this case, DQ2 will toggle at the ad-

dress being programmed.

11/30

Share Link: